EEMAX01

The Eemax EX280T2T Series Three Electric Tankless Water Heater.Whole house unit for multiple showers. Turns on in stages, based upon water flow rate. Equipped with microprocessing temp control with staged heating modules.

Eemax EX280T2T Series Three Electric Tankless Water Heater Features:
• On Demand Hot Water - no delay.
• Cut Energy Waste - flow switch activates heater only on demand (no standby heat loss).
• Continuous Hot Water - no storage capacity to run out.
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC"
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 12" x 12" x 3.5"
• Reduces Calcification.
• Field Serviceable Element - replaceable cartridge element

Eemax EX280T2T Series Three Electric Tankless Water Heater Applications:
• Engineered to turn on in stages
• Uses energy for amount of flow
• Sophisticated thermostat delivers precise outlet temperature
• Cold or Hot water feed

Cutaway View

Eemax EX280T2T Series Three Electric Tankless Water Heater Specifications:
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 12 lbs
• Volts 240V
• KW 28.5kW
• Amps 120(3x40)A
• Rise at 2 GPM 96°F
• Rise at 3 GPM 65°F
• Rise at 4 GPM 47°F
• Wire Size AWG 8
• Element - Triple replaceable Ni Chrome cartridge element inserts
• Connections: 5/8" i.d. compression (1/2" copper pipe) at bottom of unit.
• Operating pressure minimum: 25psi
• Operating pressure maximum: 150psi
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specification


EX280T2T

EEMAX02

Eemax EX144T Series Two Electric Tankless Water Heater with Single Thermostatic Control Features:

•Available thermostatic control "TC" helps insure accurate outlet temperatures (±0.5°F). Hot or Cold water feed.

• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to lavatory - integral 3/4" NPT fittings on bottom (no sweat connections).
• Cut Energy Waste - flow switch activates heater only on demand (no standby heat loss).
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Reduces calcification.
• Field Serviceable Elements replaceable cartridge element.
• Unit must be mounted on wall.

Eemax EX144TC Series Two Electric Tankless Water Heater with Single Thermostatic Control Applications:
• Residential Showers
• Industrial Processes
• Photo Processing
• Adjustable, Precise Temperature Setting ±0.5°F • Anti-scald Protection
• (TC) Only- Solar Back-up

Eemax EX144T Series Two Electric Tankless Water Heater with Single Thermostatic Control Specifications:
• Dimensions 10" x 9" x 3"
• Weight 8 lbs
• Volts 240V
• KW 15.0kW
• Amps 64(2x32)A
• Rise at 1.5 GPM 65°F
• Rise at 2 GPM 51°F
• Rise at 3 GPM 34°F
• Wire Size AWG 8
• Element - Dual replacement cartridge inserts
• Connections: 3/4" NPT at bottom of unit
•The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Note: This unit must have 2 independent electrical circuits using correctly rated wire and 2 circuit breakers.

Click Here For Specification

TC=Hot or Cold Water Feed Only
ML=Multi Lavs

Priced for EX144TC

EEMAX03

Eemax EX190T Series Two

•Available thermostatic control "TC" helps insure accurate outlet temperatures (±0.5°F). Hot or Cold water feed.

• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to lavatory - integral 3/4" NPT fittings on bottom (no sweat connections).
• Cut Energy Waste - flow switch activates heater only on demand (no standby heat loss).
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Reduces calcification.
• Field Serviceable Elements replaceable cartridge element
• Unit must be mounted on wall.

Eemax EX190T Series Two Electric Tankless Water Heater with Single Thermostatic Control Applications:
• Residential Showers
• Industrial Processes
• Photo Processing
• Adjustable, Precise Temperature Setting ±0.5°F • Anti-scald Protection
• (TC) Only- Solar Back-up

Eemax EX190T Series Two Electric Tankless Water Heater with Single Thermostatic Control Specifications:
• Dimensions 10" x 9" x 3"
• Weight 8 lbs
• Volts 240V
• KW 19.0kW
• Amps 80(2x40)A
• Rise at 1.5 GPM 87°F
• Rise at 2 GPM 65°F
• Rise at 3 GPM 43°F
• Wire Size AWG 8
• Element - Dual replacement cartridge inserts
• Connections: 3/4" NPT at bottom of unit
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Note: This unit must have 2 independent electrical circuits using correctly rated wire and 2 circuit breakers.

Click Here For Specification

TC=Hot or Cold Water Feed Only
ML=Multi Lavs

Priced for EX190TC

EEMAX04

The Eemax EX1608T Series Two Electric Tankless Water Heater with Single Thermostatic Control. This unit is ideal for serving an entire condo, apartment, smaller house or cabin. It would replace the existing tank type water heater, being fed with cold water only. Minimum switch on flow rate 0.75 GPM. Easily adjustable thermostat gives exact temperature control.

Eemax EX1608T Series Two Electric Tankless Water Heater with Single Thermostatic Control Features:

•Available thermostatic control "TC" helps insure accurate outlet temperatures (±0.5°F). Hot or Cold water feed.

• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to lavatory - integral 3/4" NPT fittings on bottom (no sweat connections).
• Cut Energy Waste - flow switch activates heater only on demand (no standby heat loss).
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Reduces calcification.
• Field Serviceable Elements replaceable cartridge element
• Unit must be mounted on wall.

Eemax EX1608T Series Two Electric Tankless Water Heater with Single Thermostatic Control Applications:
• Residential Showers
• Industrial Processes
• Photo Processing
• Adjustable, Precise Temperature Setting ±0.5°F • Anti-scald Protection
• (TC) Only- Solar Back-up

Eemax EX1608T Series Two Electric Tankless Water Heater with Single Thermostatic Control Specifications:
• Dimensions 10" x 9" x 3"
• Weight 8 lbs
• Volts 208V
• KW 16.6kW
• Amps 77(2x38.5)A
• Rise at 1.5 GPM 75°F
• Rise at 2 GPM 55°F
• Rise at 3 GPM 38°F
• Wire Size AWG 8
• Element - Dual replacement cartridge inserts
• Connections: 3/4" NPT at bottom of unit
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Note: This unit must have 2 independent electrical circuits using correctly rated wire and 2 circuit breakers.

Priced for EX1608TC

EEMAX05

Eemax EX160T Series Two Electric Tankless Water Heater with Single Thermostatic Control Features:

•Available thermostatic control "TC" helps insure accurate outlet temperatures (±0.5°F). Hot or Cold water feed.

• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to lavatory - integral 3/4" NPT fittings on bottom (no sweat connections).
• Cut Energy Waste - flow switch activates heater only on demand (no standby heat loss).
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Reduces calcification.
• Field Serviceable Elements replaceable cartridge element
• Unit must be mounted on wall.

Eemax EX160T Series Two Electric Tankless Water Heater with Single Thermostatic Control Applications:
• Residential Showers
• Industrial Processes
• Photo Processing
• Adjustable, Precise Temperature Setting ±0.5°F • Anti-scald Protection
• (TC) Only- Solar Back-up

Eemax EX160T Series Two Electric Tankless Water Heater with Single Thermostatic Control Specifications:
• Dimensions 10" x 9" x 3"
• Weight 8 lbs
• Volts 277V
• KW 16.0kW
• Amps 58(2x29)A
• Rise at 1.5 GPM 73°F
• Rise at 2 GPM 55°F
• Rise at 3 GPM 36°F
• Wire Size AWG 10
• Element - Dual replacement cartridge inserts
• Connections: 3/4" NPT at bottom of unit
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Note: This unit must have 2 independent electrical circuits using correctly rated wire and 2 circuit breakers.

Click Here For Specification

TC=Hot or Cold Water Feed Only
ML=Multi Lavs

Priced for EX160TC

EEMAX06

Eemax EX200T Series Two Electric Tankless Water Heater with Thermostatic Control Features:

•Available thermostatic control "TC" helps insure accurate outlet temperatures (±0.5°F). Hot or Cold water feed.

• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to lavatory - integral 3/4" NPT fittings on bottom (no sweat connections).
• Cut Energy Waste - flow switch activates heater only on demand (no standby heat loss).
• Available thermostatic control "T" helps insure accurate outlet temperatures (±0.5°F).
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Reduces calcification.
• Field Serviceable Elements replaceable cartridge element
• Unit must be mounted on wall.

Eemax EX200T Series Two Electric Tankless Water Heater with Thermostatic Control Applications:
• Residential Showers
• Industrial Processes
• Photo Processing
• Adjustable, Precise Temperature Setting ±0.5°F • Anti-scald Protection
• (TC) Only- Solar Back-up

Eemax EX200T Series Two Electric Tankless Water Heater with Thermostatic Control Specifications:
• Dimensions 10" x 9" x 3"
• Weight 8 lbs
• Volts 277V
• KW 20.0kW
• Amps 72(2x36)A
• Rise at 1.5 GPM 91°F
• Rise at 2 GPM 68°F
• Rise at 3 GPM 46°F
• Wire Size AWG 8
• Element - Dual replacement cartridge inserts
• Connections: 3/4" NPT at bottom of unit
•The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specification

TC=Hot or Cold Water Feed Only
ML=Multi Lavs

Priced for EX200TC

EEMAX07

Eemax EX2412T "Thermostatic" Electric Tankless Water Heater Features:
• Fully Adjustable Temperature Range between 100-140°F. Special settings of higher or lower range available upon request.
• Eliminate costly mixing valves.
• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to installation - integral 1/2" compression fittings on bottom (no sweat connections).
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Thermostatic control reduces wide temperature fluctuation.
• Prevents Legionella Bacteria Growth.
• Meets ANSI Z358.1 Tepid Water Requirements.
• Anti-scald Protection.
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"; weight 3 lbs.
• Reduces calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX2412T "Thermostatic" Electric Tankless Water Heater Applications:
• Boosters (to 180° F)
• Metering and sensor faucet compatible
• Low volume shower handset (.7 - 2 GPM)
• Schools/Hospitals/Nursing Homes/Laboratories
• Eliminate wait for hot water, long pipe runs
• Maintains accurate temperature continuously +/- 0.5°F

Eemax EX2412T "Thermostatic" Electric Tankless Water Heater Specifications:
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Volts 120V
• KW 2.4kW
• Amps 20A
• Rise at 0.5 GPM 33°F
• Wire Size AWG 10
• Element - Replaceable cartridge insert
• Connections: 1/2" compression

Eemax EX2412T "Thermostatic" Electric Tankless Water Heater Thermostat Accuracy:
• Thermostatic board maintains +/-0.5°F accuracy.
• Achieves full, pre-selected outlet temperature within 10 seconds after activation.
• Maintains consistent temperature.

•Units can be used at 208V with 25% reduced output.
•The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specification

Thermostatic Spec Options:
S- Sanitation setting 180°
FS- Factory Set temp. (ambient to 180°)

Priced for EX2412TS

EEMAX08

Eemax EX3012T "Thermostatic" Electric Tankless Water Heater Features:
• Fully Adjustable Temperature Range between 100-140°F. Special settings of higher or lower range available upon request.
• Eliminate costly mixing valves.
• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to installation - integral 1/2" compression fittings on bottom (no sweat connections).
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Thermostatic control reduces wide temperature fluctuation.
• Prevents Legionella Bacteria Growth.
• Meets ANSI Z358.1 Tepid Water Requirements.
• Anti-scald Protection.
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"; weight 3 lbs.
• Reduces calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX3012T "Thermostatic" Electric Tankless Water Heater Applications:
• Boosters (to 180° F)
• Metering and sensor faucet compatible
• Low volume shower handset (.7 - 2 GPM)
• Schools/Hospitals/Nursing Homes/Laboratories
• Eliminate wait for hot water, long pipe runs
• Maintains accurate temperature continuously +/- 0.5°F

Eemax EX3012T "Thermostatic" Electric Tankless Water Heater Specifications:
• Volts 120V
• KW 3.0kW
• Amps 25A
• Rise at 0.5 GPM 41°F
• Rise at 0.75 GPM 27°F
• Wire Size AWG 10
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Element - Replaceable cartridge insert
• Connections 1/2" compression

Eemax EX3012T "Thermostatic" Electric Tankless Water Heater Thermostat Accuracy:
• Thermostatic board maintains +/-0.5°F accuracy.
• Achieves full, pre-selected outlet temperature within 10 seconds after activation.
• Maintains consistent temperature.

• Units can be used at 208V with 25% reduced output.
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specification

TS- Sanitation setting 180°
FS- Factory Set temp. (ambient to 180°)

Priced for EX3012TS

EEMAX09

Eemax EX3512T "Thermostatic" Electric Tankless Water Heater Features:
• Fully Adjustable Temperature Range between 100-140°F. Special settings of higher or lower range available upon request.
• Eliminate costly mixing valves.
• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to installation - integral 1/2" compression fittings on bottom (no sweat connections).
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Thermostatic control reduces wide temperature fluctuation.
• Prevents Legionella Bacteria Growth.
• Meets ANSI Z358.1 Tepid Water Requirements.
• Anti-scald Protection.
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"; weight 3 lbs.
• Reduces calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX3512T "Thermostatic" Electric Tankless Water Heater Applications:
• Boosters (to 180° F)
• Metering and sensor faucet compatible
• Low volume shower handset (.7 - 2 GPM)
• Schools/Hospitals/Nursing Homes/Laboratories
• Eliminate wait for hot water, long pipe runs
• Maintains accurate temperature continuously +/- 0.5°F

Eemax EX3512T "Thermostatic" Electric Tankless Water Heater Specifications:
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Volts 120V
• KW 3.5kW
• Amps 29A
• Rise at 0.5 GPM 48°F
• Rise at 0.75 GPM 32°F
• Wire Size AWG 10
• Element - Replaceable cartridge insert
• Connections: 1/2" compression

Eemax EX3512T "Thermostatic" Electric Tankless Water Heater Thermostat Accuracy:
• Thermostatic board maintains +/-0.5°F accuracy.
• Achieves full, pre-selected outlet temperature within 10 seconds after activation.
• Maintains consistent temperature.

• Units can be used at 208V with 25% reduced output.
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specification

TS- Sanitation setting 180°
FS- Factory Set temp. (ambient to 180°)

Priced for EX3512TS

EEMAX10

Eemax EX55T "Thermostatic" Electric Tankless Water Heater Features:
• Fully Adjustable Temperature Range between 100-140°F. Special settings of higher or lower range available upon request.
• Eliminate costly mixing valves.
• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to installation - integral 1/2" compression fittings on bottom (no sweat connections).
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Thermostatic control reduces wide temperature fluctuation.
• Prevents Legionella Bacteria Growth.
• Meets ANSI Z358.1 Tepid Water Requirements.
• Anti-scald Protection.
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"; weight 3 lbs.
• Reduces calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX55T "Thermostatic" Electric Tankless Water Heater Applications:
• Boosters (to 180° F)
• Metering and sensor faucet compatible
• Low volume shower handset (.7 - 2 GPM)
• Schools/Hospitals/Nursing Homes/Laboratories
• Eliminate wait for hot water, long pipe runs
• Maintains accurate temperature continuously +/- 0.5°F

Eemax EX55T "Thermostatic" Electric Tankless Water Heater Specifications:
• Volts 240V
• KW 5.5kW
• Amps 23A
• Rise at 0.5 GPM 75°F
• Rise at 0.75 GPM 50°F
• Rise at 1.0 GPM 38°F
• Rise at 1.5 GPM 25°F
• Wire Size AWG 10
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Element - Replaceable cartridge insert
• Connections: 1/2" compression

Eemax EX55T "Thermostatic" Electric Tankless Water Heater Thermostat Accuracy:
• Thermostatic board maintains +/-0.5°F accuracy.
• Achieves full, pre-selected outlet temperature within 10 seconds after activation.
• Maintains consistent temperature.

• Units can be used at 208V with 25% reduced output.
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specification

S- Sanitation setting 180°
FS- Factory Set temp. (ambient to 180°)
ML- Multi Lav Ideal for one, two, three, lavs @ 5GPM. Will Maintain constant temp.
EE- Emergency Eye Wash. Specify for Tepid Water requirements

Priced for EX55TS

EEMAX11

Eemax EX65T "Thermostatic" Electric Tankless Water Heater Features:
• Fully Adjustable Temperature Range between 100-140°F. Special settings of higher or lower range available upon request.
• Eliminate costly mixing valves.
• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to installation - integral 1/2" compression fittings on bottom (no sweat connections).
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Thermostatic control reduces wide temperature fluctuation.
• Prevents Legionella Bacteria Growth.
• Meets ANSI Z358.1 Tepid Water Requirements.
• Anti-scald Protection.
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"; weight 3 lbs.
• Reduces calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX65T "Thermostatic" Electric Tankless Water Heater Applications:
• Boosters (to 180° F)
• Metering and sensor faucet compatible
• Low volume shower handset (.7 - 2 GPM)
• Schools/Hospitals/Nursing Homes/Laboratories
• Eliminate wait for hot water, long pipe runs
• Maintains accurate temperature continuously +/- 0.5°F

Eemax EX65T "Thermostatic" Electric Tankless Water Heater Specifications:
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Volts 240V
• KW 6.5kW
• Amps 27A
• Rise at 0.5 GPM 89°F
• Rise at 0.75 GPM 59°F
• Rise at 1.0 GPM 44°F
• Rise at 1.5 GPM 30°F
• Wire Size AWG 10
• Element - Replaceable cartridge insert
• Connections: 1/2" compression

Eemax EX65T "Thermostatic" Electric Tankless Water Heater Thermostat Accuracy:
• Thermostatic board maintains +/-0.5°F accuracy.
• Achieves full, pre-selected outlet temperature within 10 seconds after activation.
• Maintains consistent temperature.

• Units can be used at 208V with 25% reduced output.
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specification

TS- Sanitation setting 180°
FS- Factory Set temp. (ambient to 180°)
ML- Multi Lav Ideal for one, two, three, lavs @ 5GPM. Will Maintain constant temp.
EE- Emergency Eye Wash. Specify for Tepid Water requirements

Priced for EX65TS

EEMAX12

Eemax EX75T "Thermostatic" Electric Tankless Water Heater Features:
• Fully Adjustable Temperature Range between 100-140°F. Special settings of higher or lower range available upon request.
• Eliminate costly mixing valves.
• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to installation - integral 1/2" compression fittings on bottom (no sweat connections).
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Thermostatic control reduces wide temperature fluctuation.
• Prevents Legionella Bacteria Growth.
• Meets ANSI Z358.1 Tepid Water Requirements.
• Anti-scald Protection.
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"; weight 3 lbs.
• Reduces calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX75T "Thermostatic" Electric Tankless Water Heater Applications:
• Boosters (to 180° F)
• Metering and sensor faucet compatible
• Low volume shower handset (.7 - 2 GPM)
• Schools/Hospitals/Nursing Homes/Laboratories
• Eliminate wait for hot water, long pipe runs
• Maintains accurate temperature continuously +/- 0.5°F

Eemax EX75T "Thermostatic" Electric Tankless Water Heater Specifications:
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Volts 240V
• KW 7.5kW
• Amps 32A
• Rise at 0.75 GPM 68°F
• Rise at 1.0 GPM 51°F
• Rise at 1.5 GPM 34°F
• Wire Size AWG 10
• Element - Replaceable cartridge insert
• Connections: 1/2" compression

Eemax EX75T "Thermostatic" Electric Tankless Water Heater Thermostat Accuracy:
• Thermostatic board maintains +/-0.5°F accuracy.
• Achieves full, pre-selected outlet temperature within 10 seconds after activation.
• Maintains consistent temperature.

• Units can be used at 208V with 25% reduced output.
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specification

TS- Sanitation setting 180°
FS- Factory Set temp. (ambient to 180°)
ML- Multi Lav Ideal for one, two, three, lavs @ 5GPM. Will Maintain constant temp.
EE- Emergency Eye Wash. Specify for Tepid Water requirements

Priced for EX75TS

EEMAX13

Eemax EX95T "Thermostatic" Electric Tankless Water Heater Features:
• Fully Adjustable Temperature Range between 100-140°F. Special settings of higher or lower range available upon request.
• Eliminate costly mixing valves.
• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to installation - integral 1/2" compression fittings on bottom (no sweat connections).
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Thermostatic control reduces wide temperature fluctuation.
• Prevents Legionella Bacteria Growth.
• Meets ANSI Z358.1 Tepid Water Requirements.
• Anti-scald Protection.
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"; weight 3 lbs.
• Reduces calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX95T "Thermostatic" Electric Tankless Water Heater Applications:
• Boosters (to 180° F)
• Metering and sensor faucet compatible
• Low volume shower handset (.7 - 2 GPM)
• Schools/Hospitals/Nursing Homes/Laboratories
• Eliminate wait for hot water, long pipe runs
• Maintains accurate temperature continuously +/- 0.5°F

Eemax EX95T "Thermostatic" Electric Tankless Water Heater Specifications:
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Volts 240V
• KW 9.5kW
• Amps 40A
• Rise at 0.75 GPM 87°F
• Rise at 1.0 GPM 65°F
• Rise at 1.5 GPM 43°F
• Wire Size AWG 10
• Element - Replaceable cartridge insert
• Connections: 1/2" compression

Eemax EX95T "Thermostatic" Electric Tankless Water Heater Thermostat Accuracy:
• Thermostatic board maintains +/-0.5°F accuracy.
• Achieves full, pre-selected outlet temperature within 10 seconds after activation.
• Maintains consistent temperature.

• Units can be used at 208V with 25% reduced output.
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specification

S- Sanitation setting 180°
FS- Factory Set temp. (ambient to 180°)
ML- Multi Lav Ideal for one, two, three, lavs @ 5GPM. Will Maintain constant temp.
EE- Emergency Eye Wash. Specify for Tepid Water requirements

Priced for EX95TS

EEMAX14

Eemax EX8208T "Thermostatic" Electric Tankless Water Heater Features:
• Fully Adjustable Temperature Range between 100-140°F. Special settings of higher or lower range available upon request.
• Eliminate costly mixing valves.
• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to installation - integral 1/2" compression fittings on bottom (no sweat connections).
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Thermostatic control reduces wide temperature fluctuation.
• Prevents Legionella Bacteria Growth.
• Meets ANSI Z358.1 Tepid Water Requirements.
• Anti-scald Protection.
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"; weight 3 lbs.
• Reduces calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX8208T "Thermostatic" Electric Tankless Water Heater Applications:
• Boosters (to 180° F)
• Metering and sensor faucet compatible
• Low volume shower handset (.7 - 2 GPM)
• Schools/Hospitals/Nursing Homes/Laboratories
• Eliminate wait for hot water, long pipe runs
• Maintains accurate temperature continuously +/- 0.5°F

Eemax EX8208T "Thermostatic" Electric Tankless Water Heater Specifications:
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Volts 208V
• KW 8.3kW
• Amps 40A
• Rise at 0.75 GPM 76°F
• Rise at 1.0 GPM 57°F
• Rise at 1.5 GPM 38°F
• Wire Size AWG 10
• Element - Replaceable cartridge insert
• Connections: 1/2" compression

Eemax EX8208T "Thermostatic" Electric Tankless Water Heater Thermostat Accuracy:
• Thermostatic board maintains +/-0.5°F accuracy.
• Achieves full, pre-selected outlet temperature within 10 seconds after activation.
• Maintains consistent temperature.

• Units can be used at 208V with 25% reduced output.
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specification

EEMAX15

Eemax EX60T "Thermostatic" Electric Tankless Water Heater Features:
• Fully Adjustable Temperature Range between 100-140°F. Special settings of higher or lower range available upon request.
• Eliminate costly mixing valves.
• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to installation - integral 1/2" compression fittings on bottom (no sweat connections).
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Thermostatic control reduces wide temperature fluctuation.
• Prevents Legionella Bacteria Growth.
• Meets ANSI Z358.1 Tepid Water Requirements.
• Anti-scald Protection.
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"; weight 3 lbs.
• Reduces calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX60T "Thermostatic" Electric Tankless Water Heater Applications:
• Boosters (to 180° F)
• Metering and sensor faucet compatible
• Low volume shower handset (.7 - 2 GPM)
• Schools/Hospitals/Nursing Homes/Laboratories
• Eliminate wait for hot water, long pipe runs
• Maintains accurate temperature continuously +/- 0.5°F

Eemax EX60T "Thermostatic" Electric Tankless Water Heater Specifications:
• Volts 277V
• KW 6.0kW
• Amps 22A
• Rise at 0.5 GPM 81°F
• Rise at 0.75 GPM 55°F
• Rise at 1.0 GPM 41°F
• Rise at 1.5 GPM 27°F
• Wire Size AWG 10
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Element - Replaceable cartridge insert
• Connections: 1/2" compression

Eemax EX60T "Thermostatic" Electric Tankless Water Heater Thermostat Accuracy:
• Thermostatic board maintains +/-0.5°F accuracy.
• Achieves full, pre-selected outlet temperature within 10 seconds after activation.
• Maintains consistent temperature.

• Units can be used at 208V with 25% reduced output.
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specification

S- Sanitation setting 180°
FS- Factory Set temp. (ambient to 180°)
ML- Multi Lav Ideal for one, two, three, lavs @ 5GPM. Will Maintain constant temp.
EE- Emergency Eye Wash. Specify for Tepid Water requirements

Priced for EX60TS

EEMAX16

Eemax EX80T "Thermostatic" Electric Tankless Water Heater Features:
• Fully Adjustable Temperature Range between 100-140°F. Special settings of higher or lower range available upon request.
• Eliminate costly mixing valves.
• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to installation - integral 1/2" compression fittings on bottom (no sweat connections).
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Thermostatic control reduces wide temperature fluctuation.
• Prevents Legionella Bacteria Growth.
• Meets ANSI Z358.1 Tepid Water Requirements.
• Anti-scald Protection.
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"; weight 3 lbs.
• Reduces calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX80T "Thermostatic" Electric Tankless Water Heater Applications:
• Boosters (to 180° F)
• Metering and sensor faucet compatible
• Low volume shower handset (.7 - 2 GPM)
• Schools/Hospitals/Nursing Homes/Laboratories
• Eliminate wait for hot water, long pipe runs
• Maintains accurate temperature continuously +/- 0.5°F

Eemax EX80T "Thermostatic" Electric Tankless Water Heater Specifications:
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Volts 277V
• KW 8.0kW
• Amps 29A
• Rise at 0.75 GPM 73°F
• Rise at 1.0 GPM 55°F
• Rise at 1.5 GPM 36°F
• Wire Size AWG 10
• Element - Replaceable cartridge insert
• Connections: 1/2" compression

Eemax EX80T "Thermostatic" Electric Tankless Water Heater Thermostat Accuracy:
• Thermostatic board maintains +/-0.5°F accuracy.
• Achieves full, pre-selected outlet temperature within 10 seconds after activation.
• Maintains consistent temperature.

•Units can be used at 208V with 25% reduced output.
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specification

S- Sanitation setting 180°
FS- Factory Set temp. (ambient to 180°)
ML- Multi Lav Ideal for one, two, three, lavs @ 5GPM. Will Maintain constant temp.
EE- Emergency Eye Wash. Specify for Tepid Water requirements

Priced for EX80TS

EEMAX17

Eemax EX90T "Thermostatic" Electric Tankless Water Heater Features:
• Fully Adjustable Temperature Range between 100-140°F. Special settings of higher or lower range available upon request.
• Eliminate costly mixing valves.
• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to installation - integral 1/2" compression fittings on bottom (no sweat connections).
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Thermostatic control reduces wide temperature fluctuation.
• Prevents Legionella Bacteria Growth.
• Meets ANSI Z358.1 Tepid Water Requirements.
• Anti-scald Protection.
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"; weight 3 lbs.
• Reduces calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX90T "Thermostatic" Electric Tankless Water Heater Applications:
• Boosters (to 180° F)
• Metering and sensor faucet compatible
• Low volume shower handset (.7 - 2 GPM)
• Schools/Hospitals/Nursing Homes/Laboratories
• Eliminate wait for hot water, long pipe runs
• Maintains accurate temperature continuously +/- 0.5°F

Eemax EX90T "Thermostatic" Electric Tankless Water Heater Specifications:
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Volts 277V
• KW 9.0kW
• Amps 33A
• Rise at 0.75 GPM 82°F
• Rise at 1.0 GPM 61°F
• Rise at 1.5 GPM 41°F
• Rise at 2.0 GPM 31°F
• Wire Size AWG 10
• Element - Replaceable cartridge insert
• Connections: 1/2" compression

Eemax EX90T "Thermostatic" Electric Tankless Water Heater Thermostat Accuracy:
• Thermostatic board maintains +/-0.5°F accuracy.
• Achieves full, pre-selected outlet temperature within 10 seconds after activation.
• Maintains consistent temperature.

• Units can be used at 208V with 25% reduced output.
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.


Click Here For Specification

S- Sanitation setting 180°
FS- Factory Set temp. (ambient to 180°)
ML- Multi Lav Ideal for one, two, three, lavs @ 5GPM. Will Maintain constant temp.
EE- Emergency Eye Wash. Specify for Tepid Water requirements

Priced for EX90TS

EEMAX18

Eemax EX100T "Thermostatic" Electric Tankless Water Heater Features:
• Fully Adjustable Temperature Range between 100-140°F. Special settings of higher or lower range available upon request.
• Eliminate costly mixing valves.
• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to installation - integral 1/2" compression fittings on bottom (no sweat connections).
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Thermostatic control reduces wide temperature fluctuation.
• Prevents Legionella Bacteria Growth.
• Meets ANSI Z358.1 Tepid Water Requirements.
• Anti-scald Protection.
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"; weight 3 lbs.
• Reduces calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX100T "Thermostatic" Electric Tankless Water Heater Applications:
• Boosters (to 180° F)
• Metering and sensor faucet compatible
• Low volume shower handset (.7 - 2 GPM)
• Schools/Hospitals/Nursing Homes/Laboratories
• Eliminate wait for hot water, long pipe runs
• Maintains accurate temperature continuously +/- 0.5°F

Eemax EX100T "Thermostatic" Electric Tankless Water Heater Specifications:
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Volts 277V
• KW 10.0kW
• Amps 36A
• Rise at 0.75 GPM 91°F
• Rise at 1.0 GPM 68°F
• Rise at 1.5 GPM 46°F
• Rise at 2.0 GPM 34°F
• Wire Size AWG 10
• Element - Replaceable cartridge insert
• Connections: 1/2" compression

Eemax EX100T "Thermostatic" Electric Tankless Water Heater Thermostat Accuracy:
• Thermostatic board maintains +/-0.5°F accuracy.
• Achieves full, pre-selected outlet temperature within 10 seconds after activation.
• Maintains consistent temperature.

• Units can be used at 208V with 25% reduced output.
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specification

S- Sanitation setting 180°
FS- Factory Set temp. (ambient to 180°)
ML- Multi Lav Ideal for one, two, three, lavs @ 5GPM. Will Maintain constant temp.
EE- Emergency Eye Wash. Specify for Tepid Water requirements

Priced for EX100TS

EEMAX19

Eemax EX120TC "Thermostatic" Electric Tankless Water Heater Features:
• Fully Adjustable Temperature Range between 100-140°F. Special settings of higher or lower range available upon request.
• Eliminate costly mixing valves.
• On Demand Hot Water - no delay.
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to installation - integral 1/2" compression fittings on bottom (no sweat connections).
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Thermostatic control reduces wide temperature fluctuation.
• Prevents Legionella Bacteria Growth.
• Meets ANSI Z358.1 Tepid Water Requirements.
• Anti-scald Protection.
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC".
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"; weight 3 lbs.
• Reduces calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX120TC "Thermostatic" Electric Tankless Water Heater Applications:
• Boosters (to 180° F)
• Metering and sensor faucet compatible
• Low volume shower handset (.7 - 2 GPM)
• Schools/Hospitals/Nursing Homes/Laboratories
• Eliminate wait for hot water, long pipe runs
• Maintains accurate temperature continuously +/- 0.5°F

Eemax EX120TC "Thermostatic" Electric Tankless Water Heater Specifications:
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Volts 240V
• KW 11.5kW
• Amps 48A
• Rise at 0.75 GPM 104°F
• Rise at 1.0 GPM 89°F
• Rise at 1.5 GPM 52°F
• Rise at 2.0 GPM 39°F
• Wire Size AWG 6
• Element - Replaceable cartridge insert
• Connections: 1/2" compression

Eemax EX120TC "Thermostatic" Electric Tankless Water Heater Thermostat Accuracy:
• Thermostatic board maintains +/-0.5°F accuracy.
• Achieves full, pre-selected outlet temperature within 10 seconds after activation.
• Maintains consistent temperature.

• Units can be used at 208V with 25% reduced output.
• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specification

S- Sanitation setting 180°
FS- Factory Set temp. (ambient to 180°)
ML- Multi Lav Ideal for one, two, three, lavs @ 5GPM. Will Maintain constant temp.
EE- Emergency Eye Wash. Specify for Tepid Water requirements

Priced for EX120TCS

EEMAX20

Eemax EX35 "Flow Control" Electric Tankless Water Heater Features:
• On Demand Hot Water - no delay.
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to lavatory. • Mounts on wall at point-of-use.
• Hands Free - sensor and metering faucet compatible.
• Prevents Legionella Bacteria Growth
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC"
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"
• Reduces Calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX35T "Flow Control" Electric Tankless Water Heater Applications:
• Kitchen Sinks
• Bar Sinks
• Utility Sinks
• Manufacturing Facilities
• Modular Buildings and Tenant Spaces
• Dual Hand wash Sinks (DL)
• Hand Set Shower (.7 - 2 GPM)

Eemax EX35T "Flow Control" Electric Tankless Water Heater Specifications:
• Dimensions - 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• EX = Bottom Water Connection, 1/2" compression fittings
• Volts 240V
• KW 3.5kW
• Amps 14.6A
• Rise at 1.0 GPM 24°F
• Rise at .75 GPM 32°F
• Rise at .5 GPM 48°F
• Wire Size AWG - 10
• Element - Replaceable cartridge insert

• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specifications

Plumbing Orientation:
EX=Bottom Water Connections 1/2" (5/8"OD) Compression Fittings
SP=Top Water Connections 1/2" (5/8"OD) Compression Fittings

Specification Options:
SL=Single Lav-3/8" adapter supplied
FC=Flex Connector-Steel braided flex connector-
FC 176-3/8Cx1/2FIP-16" fct.supply or
FC 177-3/8Cx3/8C-16" fct.supply

Priced for EX35T

EEMAX21

Eemax EX55 "Flow Control" Electric Tankless Water Heater Features:
• On Demand Hot Water - no delay.
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to lavatory. • Mounts on wall at point-of-use.
• Hands Free - sensor and metering faucet compatible.
• Prevents Legionella Bacteria Growth
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC"
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"
• Reduces Calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX55 "Flow Control" Electric Tankless Water Heater Applications:
• Kitchen Sinks
• Bar Sinks
• Utility Sinks
• Manufacturing Facilities
• Modular Buildings and Tenant Spaces
• Hand Set Shower (.7 - 2 GPM)

Eemax EX55 "Flow Control" Electric Tankless Water Heater Specifications:
• EX = Bottom Water Connection, 1/2" compression fittings
• Volts 240V
• KW 5.5kW
• Amps 23A
• Rise at .5 GPM 75°F
• Rise at .75 GPM 50°F
• Rise at 1.0 GPM 38°F
• Rise at 1.5 GPM 25°F
• Wire Size AWG - 10
• Dimensions - 10.75" x 5.25" x 2.125"
• Weight - 3 lbs
• Element - Replaceable cartridge insert

• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specifications

Plumbing Orientation:
EX=Bottom Water Connections 1/2" (5/8"OD) Compression Fittings
SP=Top Water Connections 1/2" (5/8"OD) Compression Fittings

Specification Options:
SL=Single Lav-3/8" adapter supplied
DL=Dual Lavs-Supplied with two faucet aerators
FC=Flex Connector-Steel braided flex connector-
176-3/8Cx1/2FIP-16" fct.supply or
177-3/8Cx3/8C-16" fct.supply

Priced for EX55SL

EEMAX22

Eemax EX65 "Flow Controlled" Electric Tankless Water Heater Features:
• On Demand Hot Water - no delay.
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to lavatory. • Mounts on wall at point-of-use.
• Hands Free - sensor and metering faucet compatible.
• Prevents Legionella Bacteria Growth
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC"
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"
• Reduces Calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX65 "Flow Controlled" Electric Tankless Water Heater Applications:
• Kitchen Sinks
• Bar Sinks
• Utility Sinks
• Manufacturing Facilities
• Modular Buildings and Tenant Spaces
• Dual Hand wash Sinks (DL)
• Hand Set Shower (.7 - 2 GPM)

Eemax EX65 "Flow Controlled" Electric Tankless Water Heater Specifications:
• EX = Bottom Water Connection, 1/2" compression fittings
• Volts 240V
• KW 6.5kW
• Amps 27A
• Rise at .5 GPM 89°F
• Rise at .75 GPM 59°F
• Rise at 1.0 GPM - 44°F
• Rise at 1.5 GPM - 30°F
• Rise at 2.0 GPM 22°F
• Wire Size AWG 10
• Dimensions - 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Element - Replaceable cartridge insert

•The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specifications

Plumbing Orientation:
EX=Bottom Water Connections 1/2" (5/8"OD) Compression Fittings
SP=Top Water Connections 1/2" (5/8"OD) Compression Fittings

Specification Options:
SL=Single Lav-3/8" adapter supplied
DL=Dual Lavs-Supplied with two faucet aerators
FC=Flex Connector-Steel braided flex connector-
176-3/8Cx1/2FIP-16" fct.supply or
177-3/8Cx3/8C-16" fct.supply

Priced for EX65SL

EEMAX23

Eemax EX75 "Flow Controlled" Electric Tankless Water Heater Features:
• On Demand Hot Water - no delay.
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to lavatory. • Mounts on wall at point-of-use.
• Hands Free - sensor and metering faucet compatible.
• Prevents Legionella Bacteria Growth
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC"
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"
• Reduces Calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX75 "Flow Controlled" Electric Tankless Water Heater Applications:
• Kitchen Sinks
• Bar Sinks
• Utility Sinks
• Manufacturing Facilities
• Modular Buildings and Tenant Spaces
• Dual Hand wash Sinks (DL)
• Hand Set Shower (.7 - 2 GPM)

Eemax EX75 "Flow Controlled" Electric Tankless Water Heater Specifications:
• EX = Bottom Water Connection, 1/2" compression fittings
• Volts 240V
• KW 7.5kW
• Amps 32A
• Rise at .75 GPM 68°F
• Rise at 1.0 GPM - 51°F
• Rise at 1.5 GPM - 34°F
• Rise at 2.0 GPM 26°F
• Wire Size AWG 10
• Dimensions - 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Element - Replaceable cartridge insert

• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specifications

Plumbing Orientation:
EX=Bottom Water Connections 1/2" (5/8"OD) Compression Fittings
SP=Top Water Connections 1/2" (5/8"OD) Compression Fittings

Specification Options:
SL=Single Lav-3/8" adapter supplied
DL=Dual Lavs-Supplied with two faucet aerators
FC=Flex Connector-Steel braided flex connector-
176-3/8Cx1/2FIP-16" fct.supply or
177-3/8Cx3/8C-16" fct.supply

Priced for EX75SL

EEMAX24

Eemax EX95 "Flow Controlled" Electric Tankless Water Heater Features:
• On Demand Hot Water - no delay.
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to lavatory. • Mounts on wall at point-of-use
• Hands Free - sensor and metering faucet compatible.
• Prevents Legionella Bacteria Growth
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC"
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"
• Reduces Calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX95 "Flow Controlled" Electric Tankless Water Heater Applications:
• Kitchen Sinks
• Bar Sinks
• Utility Sinks
• Manufacturing Facilities
• Modular Buildings and Tenant Spaces
• Dual Hand wash Sinks (DL)
• Hand Set Shower (.7 - 2 GPM)

Eemax EX95 "Flow Controlled" Electric Tankless Water Heater Specifications:
• EX = Bottom Water Connection, 1/2" compression fittings
• Volts 240V
• KW 9.5kW
• Amps 40A
• Rise at .75 GPM 87°F
• Rise at 1.0 GPM - 65°F
• Rise at 1.5 GPM - 43°F
• Rise at 2.0 GPM 32°F
• Wire Size AWG 10
• Dimensions - 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Element - Replaceable cartridge insert

• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specifications

Plumbing Orientation:
EX=Bottom Water Connections 1/2" (5/8"OD) Compression Fittings
SP=Top Water Connections 1/2" (5/8"OD) Compression Fittings

Specification Options:
DL=Dual Lavs-Supplied with two faucet aerators
FC=Flex Connector-Steel braided flex connector-
176-3/8Cx1/2FIP-16" fct.supply or
177-3/8Cx3/8C-16" fct.supply

Priced for EX95DL

EEMAX25

Eemax EX8208 "Flow Controlled" Electric Tankless Water Heater Features:
• On Demand Hot Water - no delay.
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to lavatory. • Mounts on wall at point-of-use.
• Hands Free - sensor and metering faucet compatible.
• Prevents Legionella Bacteria Growth
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC"
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"
• Reduces Calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX8208 "Flow Controlled" Electric Tankless Water Heater Applications:
• Kitchen Sinks
• Bar Sinks
• Utility Sinks
• Manufacturing Facilities
• Modular Buildings and Tenant Spaces
• Dual Hand wash Sinks (DL)
• Hand Set Shower (.7 - 2 GPM)

Eemax EX8208 "Flow Controlled" Electric Tankless Water Heater Specifications:
• Dimensions 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• EX = Bottom Water Connection, 1/2" compression fittings
• Volts 208V
• KW 8.3kW
• Amps 40A
• Rise at .75 GPM 87°F
• Rise at 1.0 GPM - 57°F
• Rise at 1.5 GPM - 38°F
• Rise at 2.0 GPM 28°F
• Wire Size AWG 10
• Element - Replaceable cartridge insert

• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specifications

Plumbing Orientation:
EX=Bottom Water Connections 1/2" (5/8"OD) Compression Fittings
SP=Top Water Connections 1/2" (5/8"OD) Compression Fittings

Specification Options:
DL=Dual Lavs-Supplied with two faucet aerators
FC=Flex Connector-Steel braided flex connector-
176-3/8Cx1/2FIP-16" fct.supply or
177-3/8Cx3/8C-16" fct.supply

Priced for EX8208DL

EEMAX26

Eemax EX60 "Flow Controlled" Electric Tankless Water Heater Features:
• On Demand Hot Water - no delay.
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to lavatory. • Mounts on wall at point-of-use.
• Hands Free - sensor and metering faucet compatible.
• Prevents Legionella Bacteria Growth
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC"
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"
• Reduces Calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX60 "Flow Controlled" Electric Tankless Water Heater Applications:
• Kitchen Sinks
• Bar Sinks
• Utility Sinks
• Manufacturing Facilities
• Modular Buildings and Tenant Spaces
• Dual Hand wash Sinks (DL)
• Hand Set Shower (.7 - 2 GPM)

Eemax EX60 "Flow Controlled" Electric Tankless Water Heater Specifications:
• Dimensions - 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• EX = Bottom Water Connection, 1/2" compression fittings
• Volts 277V
• KW 6.0kW
• Amps 22A
• Rise at .5 GPM 82°F
• Rise at .75 GPM 55°F
• Rise at 1.0 GPM - 41°F
• Rise at 1.5 GPM - 27°F
• Rise at 2.0 GPM 20°F
• Wire Size AWG 10
• Element - Replaceable cartridge insert

• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed.

Click Here For Specifications

Plumbing Orientation:
EX=Bottom Water Connections 1/2" (5/8"OD) Compression Fittings
SP=Top Water Connections 1/2" (5/8"OD) Compression Fittings

Specification Options:
SL=Single Lav-3/8" adapter supplied
DL=Dual Lavs-Supplied with two faucet aerators
FC=Flex Connector-Steel braided flex connector-
176-3/8Cx1/2FIP-16" fct.supply or
177-3/8Cx3/8C-16" fct.supply

Priced for EX60SL

EEMAX27

Eemax EX80 "Flow Controlled" Electric Tankless Water Heater Features:
• On Demand Hot Water - no delay.
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to lavatory. • Mounts on wall at point-of-use.
• Hands Free - sensor and metering faucet compatible.
• Prevents Legionella Bacteria Growth
• Designed for Durability - constructed of high strength reinforced "ENGINEERING PLASTIC"
• Ni Chrome Element - a unique, patented flow path ensures optimum heat transfer and extended element life.
• Compact Size - dimensions 10.75"x5.25"x2.125"
• Reduces Calcification.
• Space Saving Installation - under sink, point-of-use.
• Field Serviceable Element - replaceable cartridge element.
• Complies with handicap requirements.

Eemax EX80 "Flow Controlled" Electric Tankless Water Heater Applications:
• Kitchen Sinks
• Bar Sinks
• Utility Sinks
• Manufacturing Facilities
• Modular Buildings and Tenant Spaces
• Dual Hand wash Sinks (DL)
• Hand Set Shower (.7 - 2 GPM)

Eemax EX80 "Flow Controlled" Electric Tankless Water Heater Specifications:
• EX = Bottom Water Connection, 1/2" compression fittings
• Volts 277V
• KW 8.0kW
• Amps 29A
• Rise at .75 GPM 73°F
• Rise at 1.0 GPM - 55°F
• Rise at 1.5 GPM - 36°F
• Rise at 2.0 GPM 27°F
• Wire Size AWG 10
• Dimensions - 10.75" x 5.25" x 2.125"
• Weight 3 lbs
• Element - Replaceable cartridge insert

• The voltage, amperage, and circuit breaker specifications must be met for this heater to function. Please make sure all requirements are met before purchasing this heater. Manufacturer's start up procedures must be observed

Click Here For Specifications

Plumbing Orientation:
EX=Bottom Water Connections 1/2" (5/8"OD) Compression Fittings
SP=Top Water Connections 1/2" (5/8"OD) Compression Fittings

Specification Options:
DL=Dual Lavs-Supplied with two faucet aerators
FC=Flex Connector-Steel braided flex connector-
176-3/8Cx1/2FIP-16" fct.supply or
177-3/8Cx3/8C-16" fct.supply

Priced for EX80DL

EEMAX28

Eemax EX90 "Flow Controlled" Electric Tankless Water Heater Features:
• On Demand Hot Water - no delay.
• Cut Energy Waste -flow switch activates heater only on demand (no standby heat loss).
• Continuous Hot Water - no storage capacity to run out.
• Reduces Installation Cost - no T & P relief valve needed (check local codes).
• Easy Installation - only one cold water line need be brought to lavatory. • Mounts on wall at point-of-use.
• Hands Free - sensor and metering faucet compatible.
• Prevents Legionella Bacteria Growth
• Designed for Durability - constructed of high strength reinforced "ENGINEERING